John Sayers' Recording Studio Design Forum

Hello everyone ...
I'm setting up a project studio and I'd like to know how best to place my point of control
solution 1 http://www.facebook.com/photo.php?fbid=10150147382954876&set=a.10150147382894876.294142.772634875&theater
or
solution 2 http://www.facebook.com/photo.php?fbid=10150147382954876&set=a.10150147382894876.294142.772634875&theater#!/photo.php?fbid=10150147383004876&set=a.10150147382894876.294142.772634875&theater&pid=6276558&id=772634875

Many thanks to all who give me advice

ps ... sorry for my bad English

fatmike

welcome! please update your profile to include your location and please provide some additional information on what you are trying to achieve. thanks!

_________________
Glenn

hello ... you're right ... I updated my profile as you asked ...

I am here simply to ask for advice on how to set up my project studio ... because I'm about to make some changes, I wanted one of your suggestions in this regard.
hello to all those who will provide ...
good music to all

ps. Always sorry for my bad English

Definitely solution #2! The first one would be terrible for several reasons, but #2 is workable. You will still need a lot of acoustic treatment in that room, but layout #2 is the way to do it, for sure.

Why do you have that diagonal cut across the wall of the live room?


- Stuart -

_________________
I want this studio to amaze people. "That'll do" doesn't amaze people.

hello and thanks for the suggestion ...
that cut was required due to a concrete pillar ...

have a solution for that??

thanks so much for all ...

you have any suggestions for me on acoustic treatment?
thanks ...

PS...sorry for my bad english

hello...
I'd be willing to pay for the solutions the acoustic treatment of the study...
are about to dismantle my old studio

help me...

fatmike

Good thing one of the Mods took a look, I do not have a facebook account (do not have the time) so could not see the picture(s)

_________________
Brien Holcombe
_____________________________________________
Sound: You can't stop it, you can only try to contain it.

hello ... you're right
then ...
I got a little space in my garage and I have separated the two rooms with walls made ​​detached from each other with different insulating materials;
wooden structure filled with rock wool, covered with plaster board, sheet Isolmant, a layer of plywood and then I glued on wood panels, acoustic material ... but I think I did the right thing .. .
I saw that there are people on this forum very prepared and knowledgeable and I am asking for help to you for suggestions for, with the space I have, the best solution and the best obtainable ...

a big thanks to all who will give me important tips ...

Thanks to all in advance ...

fatmike

PS...always sorry for my bad english...

i think the #1 design is the way to go

_________________
Glenn

and why? ... there are suggestions on acoustic treatment to optimize listening?

the position is more symmetrical in the room and you have a longer length behind you. as far as treatments, the soffit approach is good. the ceiling will need a cloud and you should consider some movable absorption on either side for first reflection points during mix down. scatter absorption on the ceiling behind and absorption/diffusion on the back walls.

_________________
Glenn

hello glenn and thank you for your interest and for the advice ...
you would know me practical examples for correcting my problems?

I thank you immensely

the sides will need some cloth covered absorbers on your first reflection points - you might have to make one to slide into place on the window side during mix down. on the ceiling - a hard backed cloud - 19mm plywood and 19mm MDF screwed and glued with a 100mm cloth covered absorber on the face of it - about 250mm from the edges of the wall and front soffits and extending back about 300mm past your sitting position. angle it slightly so you still have clearance on the top monitor in the soffit and some air gap. along the rest of the room walls and ceiling - scattered patches of 100mm thick cloth covered absorbers about 400mm x 400mm spaced apart about 400mm. on the back wall (from the desk) same thing but make the gaps between the absorbers 250mm or so.

_________________
Glenn

thanks for your valuable advice, but I need some clarification:
it is clear that I should create something that I cover the glass and Dov
- As regards the ceiling ... I have to create a kind of sandwich:
plywood - foam - MDF or simply the two sticks glued together?
- the opposite wall to the speakers should I use the panels seconded by
wall of 40 cm?
- to the side walls, the same panels but detached from the wall of 25 cm?

thanks for the advice ...
you are a myth